OTRATTW
HomeAbout UsProductssearchContact
  
Order status View Order Status Checkout Checkout Email Email store
Search our store   
OTRATTW
P.O. Box 425
Cupertino, CA 95015
(408)253-5337
Email Us

 

Home » Contura V Laser Etched Rockers & Switches » Accessories

 Checkout
Product ID: VVPZC2G-500
Manufacturer: Carling Technologies
V-series Contura V sealed rocker switch, STEREO ROCKER
V-series Contura V sealed rocker switch, STEREO ROCKER
  (Enlarge)  

ROCKER ONLY-

  • This is just the top part of the switch and is purchased if you already have switches and need to either replace the existing rockers or have purchased switch bodies elsewhere.

________________________________________________________________________________________________________________________________________________

SINGLE LIGHTED SWITCHES

V1D1BC0B -SPST OFF/ON – Red LED

V1D1BN0B-SPST OFF/ON – Amber LED

V1D1BH0B-SPST OFF/ON – Green LED

  • Upper LED that is ON when the switch is turned ON.
  • Three terminal switches with no rear barriers.  Use 1/4" female disconnects or VCH housing. (Packard terminals for the rear housing are sold separately)

________________________________________________________________________________________________________________________________________________

DOUBLE LIGHTED SWITCHES

V1D1FCTB- SPST OFF/ON- Red upper, daylight bright red lower LED

V1D1FNTB- SPST OFF/ON- Amber upper, daylight bright red lower LED

V1D1FBBB- SPST OFF/ON- Blue upper and lower LED.  These LEDs are bright and consideration should be given on where you plan to install the switches as they might be a distraction at night.  Not recommended for pillar or above the windshield switch panels.

  • Upper LED is independently wired.
  • Lower LED is ON when the switch is turned ON.
  • Each LED has its own ground terminal.
  • Five terminal switch with no rear barriers between terminals
  • Use insulated 1/4" female disconnects or the VCH rear connector housing.  (Packard terminals for the rear housing are sold separately)

 

V1D1GHCB- SPST OFF/ON – Green upper LED, red lower LED

  • Upper LED is independently wired
  • Lower LED is ON when the switch is turned ON.
  • Common internal ground for the LEDs
  • Four terminal switch with no rear barriers between terminals
  • Use insulated 1/4" female disconnects or the VCH rear connector housing.  (Packard terminals for the rear housing are sold separately)

_______________________________________________________________________

 

V1D1JCHB- SPST OFF/ON – Red upper, green lower LED

V1D1JCNB- SPST OFF/ON – Red upper, amber lower LED

  • Upper LED is ON when the switch is turned ON.
  • Lower LED is independently wired.
  • Each LED has its own ground terminal.
  • Five terminal switch with no rear barriers between terminals
  • Use insulated 1/4" female disconnects or the VCH rear connector housing.  (Packard terminals for the rear housing are sold separately)
  • This switch has the same terminal layout and lighting configuration used by ARB

 

________________________________________________________________________
  

V6D2UHNB – SPDT ON/OFF/ON –

  • Green upper LED
  • Amber lower LED
  • Both LEDs are independently wired and have separate ground terminals. 
  • This switch could be installed upside down to place the amber LED at top, green LED at the bottom
  • Seven terminal switch with no rear barriers between the terminals
  • Use insulated ¼” female disconnects or the VC1-01 connector housing (Packard terminals for the rear housing are sold separately)
  • Verify that a SPDT switch is suitable for your application prior to purchasing this switch.  If a DPDT switch is required use the VJD2UHTB or similar VJD model switch.

_______________________________________________________________________

 

General Switch Specifications:

  • 12 and 18 volt switches are rated 20 amps
  • 24 volt switches are rated 15 amps
  • Hole cutout required is .830(21.08) by 1.45(36.83)

Panel thickness range:

0 Gasket - .030 to .250 (.76mm to 4.76mm)

1 Gasket - .030 to .109 & .147 to .157  (.76 to 2.77mm & 3.73 to 3.98mm)

Recommended: No gasket with panel thickness of .032, .062, .093, .125, .187, .250

Additional information is available through Carling Technology’s website located here:

http://www.carlingtech.com

 

 

 

 
:
Stereo Rocker: Music Note symbol, STEREO text
Speaker symbol, STEREO text
Music note symbol, custom text (add to remarks at checkout)
Speaker symbol, custom text (add to remarks at checkout)
 
Price: $5.25

 
« Previous | Next »

 
Product Reviews

No Reviews For This Product.


Shopping cart  Shopping cart
0 Product(s) in cart
Total $0.00
» Checkout
News


CONTURA V ROCKERS


Please allow 3 to 4 business days (weekends and holidays not included) for laser etch rockers orders to be completed. Custom orders require a minimum of 7 business days. Custom rockers are not returnable under any circumstances. This includes any graphic and/or text changes.

IMPORTANT REMAINDER

OTRATTW is not responsible for lost or stolen packages. Insurance is available at checkout and is recommended.




WIRING DIAGRAMS


Wiring diagrams are now available for download. Click on the following link - Wiring Diagrams

© Copyright 2008
OTRATTW
by Leapfrog Studios

PayPal
home | about us | products | search | view cart | contact us